Creative Lighting

Lighting for Stop Motion Photography

Lighting for stop motion: prevent flicker with steady LEDs, block daylight, and lock exposure, white balance and frame rate for smooth animation.

On this page
  1. Why flicker happens
  2. Choosing flicker-free lights
  3. Best lights for a miniature set
  4. Camera settings for stop motion
  5. Strobes or continuous light
  6. Keeping the set steady
  7. Fixing flicker in post
  8. Software
  9. Common mistakes
  10. Safety

In stop motion, the lighting problem that matters most is flicker: brightness or color that changes from one frame to the next. The light has to stay the same across every frame. That means blocking daylight, using steady continuous light, and locking every camera setting that could change between shots.

Why flicker happens

  • Daylight. Window light changes from minute to minute, and clouds make it worse. Block all daylight with blackout material.
  • Unsteady lights. Some LEDs flicker, especially when they are dimmed or run from failing batteries. Mains-powered lights are steadier than draining batteries.
  • Aperture. DSLR lenses stop down slightly differently each time you shoot, so the exposure can shift a little. Use a lens with a manual aperture, or try the “lens twist” trick, which depends on the camera system.
  • Auto settings. Auto ISO, auto white balance and auto exposure can change the image on every frame.

Choosing flicker-free lights

  • Choose continuous LEDs rated flicker-free, with a CRI of 95 or higher.
  • Run them from mains power where you can.
  • For a small set, mini LED panels (or a DIY LED panel), small fresnels or pin spots, and card reflectors give control without much heat.
  • Tungsten and halogen lamps run hot and can soften plasticine or melt foam. LEDs run cooler.

Best lights for a miniature set

What are the best lights for miniature photography? For a miniature set, look for small, steady, controllable lights: mini LED panels, small fresnels, pin spots and card reflectors. They give you a directional look without much heat. Place them so they do not warm the plasticine or foam, and tape them down.

Camera settings for stop motion

What are the best camera settings for stop motion photography? Set the camera to fully manual:

  • Exposure: manual, with a fixed shutter speed and aperture.
  • ISO: fixed. Turn off Auto ISO.
  • White balance: a fixed Kelvin setting. Turn off auto white balance.
  • Focus: manual, and locked.
  • Stabilization: off when the camera is on a tripod.
  • Dynamic-range optimizer: off.

For frame rate, many animators shoot 12 frames a second and hold each frame twice for 24 fps playback, which is called shooting “on twos”. Others shoot 24 fps and change the frame every time, which is “on ones”. At 12 fps, one second of footage is 12 frames.

Shoot tethered to a computer, or use a remote trigger so you never touch the camera between frames.

Strobes or continuous light

Strobes can work if their power stays fixed from shot to shot. They vary slightly from frame to frame, though, and they are harder to preview. Continuous light is easier to check before each frame, so it is the usual choice.

Keeping the set steady

  • Tape down stands, lights and the camera. One bump can ruin continuity.
  • Animators’ bodies and clothing bounce light onto the set. Wear dark clothing.
  • Check the set before each frame, and make sure nothing has moved.

Fixing flicker in post

Deflicker tools exist in post-production, such as DaVinci Resolve Studio and After Effects plugins. They can reduce flicker, but it is better to prevent it on set.

Software

Dragonframe (professional) and Stop Motion Studio (consumer) both offer onion skinning, which shows the previous frame over the live view so you can judge the next movement.

Common mistakes

  • Thinking window light is fine when it’s cloudy. Clouds cause flicker.
  • Assuming auto mode keeps frames consistent. It changes the exposure every frame.
  • Believing flicker always comes from the lights. Aperture and auto settings cause it too.
  • Ruling out strobes. They can work at fixed power.

Safety

Tungsten and halogen lamps can soften plasticine and melt foam. Keep them away from the set, or use LEDs, which run cooler.

The complete guide to creative lighting

Smoke and Fog Photography Lighting
Read the guide

Keep exploring

Guides from other topics

All topics →