Smoke and fog only show up in a photo when they scatter light, so where you put the light matters more than how much smoke you make. Backlight or side light the haze, keep the background dark, and use a smoke source that suits the scene. The sections below cover the position of the light, the smoke sources, settings with and without flash, and safety.
Why light position decides whether smoke shows
Aim the light so it points roughly toward the camera, about 90–180° from the lens axis. Light from beside the camera, or front light, tends to make fog look flat and gray and can hide it almost completely. Side light gives more texture and depth, and backlight gives the glow.
The shape of the light matters as well. A hard source, such as a bare flash, a fresnel or an optical snoot, makes defined beams. A softbox just fills the haze with an even glow. If you want visible shafts, keep the source small. If you want soft atmosphere, go wide.
For the same effect with a natural or artificial fog, see how to make fog visible on camera.
Choosing a smoke source
Each smoke source behaves differently, so pick one for the look you want:
- Fogger: a fog machine that heats glycol or glycerin-and-water fluid. It makes dense fog that clears faster than haze.
- Hazer: a machine that makes finer particles. Haze hangs in the air longer, spreads more evenly, and suits visible light beams.
- Low-lying fog: dry ice in warm water, or a chilled fog unit, keeps the fog near the floor.
- Incense: good for small, close scenes. Use it against a black background.
- Canned aerosol haze: handy for small, one-off shots.
Typical consumer fog machines draw about 400–1,500 W, and warm-up takes roughly 3–10 minutes depending on the model. Check your manual for exact figures. For how to fill, warm up and fire a machine, see how to use a fog smoke machine.
Smoke with flash
An external speedlight gives you the most control. Set it to low power, around 1/32 to 1/128, which gives a very short flash duration that freezes the smoke’s movement, the same principle behind high-speed flash photography. Flash duration varies by model, so test your own unit.
A starting point:
- Camera in manual mode
- Aperture around f/8–f/11
- ISO 100–200
- Shutter speed of 1/200 s, within your camera’s flash sync speed
Pre-focus manually on a pencil or on the tip of an incense stick, at the place where the smoke rises. Put a black background 1–2 m (3–6 ft) behind the smoke, and light the smoke from one side or slightly behind. Flag the light so it does not spill onto the background or into the lens.
Smoke without an external flash
You do not need studio strobes. A dark room and one bright light are enough. Place a bright LED or flashlight to the side of the smoke. As a starting point, try a shutter speed between 1/250 and 1/1000 s, a wide aperture and ISO 800–3200. The right values depend on how bright your light is, so adjust from there.
You can also bounce the pop-up flash off a card held to the side. The bounced light is softer and gives the smoke less defined edges.
Adding color and tone
Gels on a backlight can tint the smoke. Complementary pairs, such as teal and orange, separate the layers of haze. For more on gel choices, see colored gels for photography lights.
In post-processing, inverting a smoke photo on a white background gives dark smoke on white. Gradient maps or hue shifts can add color. Keep the edits subtle so the image still looks like the scene you shot.
Fake smoke, rain and outdoor fog
How to make fake smoke for a photoshoot? Use a commercial fog or haze machine, a canned aerosol haze, or incense for a small set. Do not make your own fog fluid. Wrong fluids can clog the heater, and some can be toxic. The post-processing steps above can add a smoky look to a clean shot.
Can I use a fog machine in the rain? Avoid it. Rain disperses fog quickly, and water near mains power is a shock risk. Unless the machine is rated for outdoor use, keep it dry and indoors, and check the manual.
Outdoors, wind clears fog quickly. Place the machine upwind of the scene so the fog drifts across it, and shoot straight away.
Common mistakes
- Lighting the fog from the front. The fog disappears.
- Making too much fog. It washes out the subject and kills contrast.
- Assuming you need studio strobes. A flashlight in a dark room works.
- Assuming fog won’t set off alarms. Photoelectric smoke detectors often respond to fog.
Safety
- Fog machine nozzles and their output get hot. Keep the machine at least 1 m (3 ft) from people and objects, and never point it at anyone at close range.
- Glycol fog can irritate asthma and sensitive airways. Ventilate between takes.
- Dry ice is around −78.5 °C (−109 °F). Handle it with gloves, and remember that CO2 builds up in low, enclosed spaces.
- Fog residue makes floors slippery, so clean up after the shoot.
- Keep incense away from flammable backdrops, and never leave it burning unattended.
- Tell venue staff before you start. Some venues need the smoke alarms isolated.