DIY Lighting

Using Household Lamps and Flashlights for Photography

Use household lamps and flashlights for photography. Learn bulb color temperature, CRI, white balance, diffusion and light painting with a flashlight.

On this page
  1. Can household lamps work for photography?
  2. Check the bulb first
  3. Set a custom white balance
  4. Make the light softer or harder
  5. A clamp lamp as a key light
  6. Natural light near household lamps
  7. Flashlights for hard light and light painting
  8. Flicker and shutter speed
  9. Common mistakes
  10. Safety

Can household lamps work for photography?

Yes, for many everyday shots. A clamp lamp or desk lamp with a movable head gives you a light you can aim, and you may already own one. The trade-off is output. Household bulbs are weak, so expect to use a tripod, a higher ISO or a wider aperture.

Check the bulb first

Bulb labels give a color temperature in kelvin:

Label Typical color temperature Look
Soft white or warm white About 2700K Warm, orange
Bright white or cool white About 3500 to 4100K Neutral to cool
Daylight About 5000 to 6500K Blue-white

Higher kelvin means a cooler, bluer light. Lower kelvin means a warmer, more orange light.

Household LEDs are often around CRI 80. For accurate skin tones, buy bulbs that list CRI 90 or higher. Use the same bulb type in every lamp you point at the subject. Mismatched bulbs give color casts that are hard to fix later.

Set a custom white balance

Place a gray card where the subject will sit, under the actual lamp, and set a custom white balance from it. Shoot in RAW if your camera allows it, so you can fine-tune the color afterward.

Make the light softer or harder

  • Shade on: a lampshade softens the light and often warms it.
  • Shade off: the bare bulb gives harder, more directional light.
  • Add diffusion: a sheet of parchment or white fabric in front of the lamp softens it. Each layer costs roughly one stop.
  • Think about size: brighter lamps do not make softer light. Source size and distance do.

A clamp lamp as a key light

Clamp the lamp to a stand or the edge of a table. Aim it at about 45 degrees to the subject, slightly above eye level. Put a white foam board reflector on the opposite side to bounce light back into the shadows. This is a simple, controllable setup that uses almost nothing you need to buy.

Natural light near household lamps

How do you use natural light for indoor photography? Put the subject near a window and avoid direct sun on the face, which creates harsh shadows. In the middle of the day, place the subject at an angle to the window, around 45 degrees, for softer shadows. When the sun is low and streams through the window, try backlighting, and expose for the subject rather than the bright window.

Window light and household lamps often clash. Daylight is bluer than most warm bulbs, so mixing them gives orange and blue casts. Turn off overhead lights and lamps when you shoot by a window, or pick one artificial light and set your white balance to match it.

Flashlights for hard light and light painting

A flashlight makes a narrow beam, which suits three jobs:

  • Spotlighting a product. A hard, directional beam shows texture and edges.
  • Snoots. Roll black card into a tube or use a cardboard tube over the flashlight to narrow the beam further.
  • Light painting. Put the camera on a tripod in a dark room, use a base ISO and an aperture of f/8 to f/11, and try an exposure of about 10 to 30 seconds. Move the flashlight across the scene during the exposure.

Many flashlights render cool, at about 6000K or higher, and at low CRI. Check the spec sheet before you use one for portraits.

Flicker and shutter speed

Many mains-powered lights flicker at twice the mains frequency: 100 Hz in 50 Hz regions and 120 Hz in 60 Hz regions. Cheap LEDs can flicker at other rates too. If you see bands in the frame, try a shutter speed of 1/50 second in a 50 Hz region or 1/60 second in a 60 Hz region. This works for mains flicker, but not for every dimmer, so test your setup.

Common mistakes

  • Treating “daylight” bulbs as sunlight. Their color quality does not match sunlight.
  • Using a phone flashlight as a key light. It is usually too small and harsh to be useful for portraits.
  • Expecting brighter lamps to give softer light. Source size and distance matter more.
  • Mixing warm bulbs with other light sources. Warm casts are hard to correct after the shoot.

Safety

  • Halogen torchiere lamps can reach 300 to 500 watts and get dangerously hot. Keep them away from curtains and paper diffusers.
  • Keep incandescent bulbs away from anything taped over them.
  • Do not shine a high-output flashlight into anyone’s eyes.

The complete guide to diy lighting

DIY Photography Lighting: Homemade Ideas That Work
Read the guide

Keep exploring

Guides from other topics

All topics →