What a tube light is good for
A tube light is a long, narrow light source. Its shape suits edge and rim lighting, hair light, light painting, and practical lights that show in the frame, such as a glowing shelf or a bar behind the subject. It does a different job from a ring light or a softbox, so choose it for the look you want.
If you need a flat, even continuous light instead, a DIY LED panel suits better.
Parts
- Aluminum channel with a milky or opal diffuser. Channels are sold in 1-meter and 2-meter lengths. The channel doubles as a heat sink.
- LED strip. Use 12V, with CRI 90 or higher. 2835 or 5050 strips work well.
- Power. A 12V DC adapter, a protected battery pack, or a USB-C power delivery (PD) trigger board set to 12V.
- Mount. A super clamp, a spring clamp, or a 1/4”-20 threaded end cap.
A frosted polycarbonate or acrylic tube can replace the aluminum channel. In that case, make sure the strip has a clear path for heat.
Choosing the strip
- Pick a white strip with CRI 90 or higher. RGB strips can produce colored effects, but their white light renders skin poorly.
- Choose a denser strip. Strips with 120 LEDs per meter, or COB strips, give more even light with fewer dots.
- Plan for heat. More LEDs per meter means more heat. Dense strips need good heat sinking, so keep them in the channel.
- Check the power draw. A 12V 5050 strip at 60 LEDs per meter is often listed at about 14 watts per meter. Check your datasheet.
Building the tube
- Cut the channel to length.
- Cut the strip only at the marked cut points.
- Stick the strip along the center of the channel base.
- Connect the wires with proper connectors, matching + and − polarity.
- Test the strip on the bench before you close the channel.
- Snap the diffuser into place and mount the tube.
Avoiding visible LED dots
Leave about 10 to 15 mm between the strip and the diffuser. The right gap depends on the density of the LEDs, so treat this as a starting point. If you still see dots, try a denser strip or add more distance. A sheet of diffusion over the front softens the light further, but it also costs light, so add it only if you need it.
Powering the tube
- Mains-powered 12V adapter. This is the simplest option and gives the most output. Use a certified, enclosed supply.
- Battery. A 3S lithium-ion pack (11.1 V nominal, 12.6 V full) works well with a battery management system (BMS) and a fuse near the battery. Runtime is not simply the pack’s watt-hours divided by the strip’s watts. Converter losses often cut runtime by around 10 to 15%.
- USB power bank. A power bank cannot drive a 12V strip directly. Use a USB-C PD trigger board set to 12V, or a boost converter. A 5V USB strip runs straight from a power bank, but it gives much less light.
Repurposed LED T8 tubes are another option. Ballast-bypass types need mains rewiring, so have a qualified person do that work, or stay with a low-voltage build.
Mounting and use
- Clamp the tube to a stand with a super clamp, or use a 1/4”-20 threaded end.
- Common placements include an edge or rim light behind the subject, a hair light from above, a practical light in a room shot, or light painting.
- For light painting, put the camera on a tripod in a dark room, open the shutter for a long exposure and move the tube through the frame.
Common mistakes
- Expecting RGB strips to render accurate white. Use a white, high-CRI strip for portraits.
- Running a 12V strip from a plain USB power bank. It needs a PD trigger or a boost converter.
- Assuming dense strips need less cooling. They produce more heat, so they need more heat sinking.
- Sealing the strip in a tube with no heat path. Heat shortens LED life and shifts color.
Safety
- Use only protected lithium-ion cells, or a pack with a BMS, and add a fuse close to the battery.
- Use a certified, enclosed DC adapter.
- Do not seal strips in a tube without a heat path.
- Leave mains-side rewiring to a qualified person.