What a reflector does
A reflector does not create light. It redirects light that is already there, from a window, a lamp or the sun, into the shadows on your subject. It works with natural light and with flash, and it is useful for video too.
Distance matters. Moving the reflector closer to the subject adds much more fill, because light falls off with distance.
Sizes and materials
- Foam board. A 20 × 30 inch sheet is common at dollar stores, and a 30 × 40 inch sheet is common at art and craft stores. Foam board is about 3/16 inch (5 mm) thick. Dollar store prices are roughly $1 to $2 a sheet, but they vary by region.
- Insulation board. A 4 × 8 foot polystyrene board makes a large reflector. Some boards come with white on one side and silver on the other.
- Aluminum foil. Ordinary kitchen foil works, but it needs a flat, smooth backing and some adhesive.
- Spray adhesive. A product such as 3M Super 77 works well. Use it in a ventilated area, away from flames.
- Gaffer tape. Use it to seal the edges so the foil does not peel.
Build a foil reflector
- Cut the board. A 30 × 40 inch board is a useful starting size for portrait fill.
- Choose the finish. Smooth foil gives a brighter, more specular reflection. For a softer spread, crinkle the foil, then flatten it again before you glue it down.
- Cut the foil. Cut the foil a few inches larger than the board.
- Spray the adhesive. Spray the board, or the back of the foil, following the product’s directions.
- Lay the foil. Press the foil on from the center outward to avoid bubbles, and fold the overhang around the edges to the back.
- Seal the edges. Run gaffer tape along the edges so the foil stays flat.
Choosing the surface
- Silver foil reflects the most light, like a silver reflector, and gives a bright, specular look. Up close, it can look harsh.
- White board gives a softer, gentler fill that is often easier on skin. Test white and silver at the same distance to see which you prefer.
- Gold foil or gold wrapping paper warms the reflected light. Use it sparingly on skin.
- Black board absorbs light. Use it as negative fill or a flag to deepen shadows.
Two-in-one and V-flat reflectors
- Two-in-one. Leave one side white and cover the other with foil. Flip the board to change the fill.
- V-flat. Hinge two 30 × 40 inch boards together along one long edge with gaffer tape. Open them into a V, and the boards stand on their own. Each side gives you a reflecting face, and the V can also work as a background.
Positioning the reflector
- Angle. The angle of incidence equals the angle of reflection. Tilt the board so it bounces light from your source toward the shadow side of the subject.
- Distance. Move the board closer for more fill, and farther for less.
- Clamshell. Place the reflector below the face, with the key light above, for a classic portrait setup.
Hold the board with A-clamps on a light stand, or prop it against a chair or a stack of books.
For a softer key light to pair with the reflector, see how to make a DIY softbox.
Quick alternatives
- Car windshield sunshade. A silver or white sunshade is a cheap, quick reflector. It folds for storage.
- Insulation board. A large board gives a big reflecting surface, but it is harder to hold steady outdoors.
Common mistakes
- Thinking a reflector creates light. It only redirects what is already there.
- Using silver by default. Up close, it can look harsh and specular.
- Worrying about shiny versus dull foil. The difference is small.
- Expecting a reflector to replace a second light. A reflector cannot do the job if the key light is far away or weak.
Safety
- Do not aim a silver board at anyone’s eyes, especially when it catches direct sun. The glare is uncomfortable and can be harmful.
- Large boards catch wind outdoors. Hold them or secure them.
- Use spray adhesive in a ventilated area, away from flames.