Flash can make a photo look much better or much worse. The difference usually comes down to three choices: which flash you use, how bright it is compared with the room, and where it points. This guide covers those basics in the order most beginners need them. Each section links to a deeper article on this site.
What “flash” means in this guide
Here, “flash” means a light that fires for a fraction of a second to light a subject. It can sit on the camera or be placed off to one side.
The phrase “flashlight photography” is used in two ways. Some people use it for flash. Others mean light painting, which uses a handheld flashlight during a long exposure, usually on a tripod. Light painting is a different technique, and this guide is about flash.
The three main kinds of flash
Sources don’t agree on one list. The most common split is by hardware:
- Built-in or pop-up flash. It sits in the camera body. It’s convenient, but it has low power, and it fires straight at the subject, which often gives harsh light.
- Speedlight (hot-shoe flash). It mounts in the camera’s hot shoe. It has more power, a head that tilts and swivels for bouncing, and usually supports TTL.
- Studio strobe. It’s a powerful unit, often mains-powered or battery-powered, and used with modifiers. It’s mostly used off the camera.
For a fuller comparison, see what are the three types of flash?
How flash and room light combine
Every flash photo has two exposures mixed together: the ambient light already in the room or outdoors, and the flash. Three rules cover most situations:
- Shutter speed mainly controls the ambient light, as long as you stay at or below the flash sync speed. A flash burst is so short that shutter speed barely changes how much light it adds.
- Aperture and ISO affect both the flash and the ambient light.
- Flash power and distance control the flash contribution. This follows the inverse square law: doubling the distance between flash and subject cuts the light on the subject to a quarter, which is two stops.
Setting the ambient light first, then adding flash for the subject, is the core workflow. The full steps are in balancing flash and ambient light.
Power settings and the inverse square rule
In manual mode, flash output is shown as fractions of full power: 1/1, 1/2, 1/4, and so on, down to 1/64 or 1/128 depending on the unit. Each step halves the output, which is one stop. Many units also adjust in third-stop steps.
Because of the inverse square law, moving the flash further from the subject needs a higher power setting to keep the same exposure. Keeping the distance the same from shot to shot is the easiest way to get consistent results.
TTL or manual mode
Flash can set its own output or follow your settings:
- TTL (through the lens) lets the camera read a short pre-flash and set the main burst. It suits moving subjects and changing distances.
- Manual keeps the output you choose. It gives repeatable results, which is useful in studios and with several lights.
Neither mode is better in every case. The comparison and a decision rule are in TTL vs manual flash: which mode to use and when.
Turning flash on and checking that it fires
If the flash doesn’t fire, check the camera settings first:
- Built-in flash: raise the flash or press the flash button, and make sure the flash mode is enabled. Some camera modes turn the flash off.
- Speedlight: switch the unit on and wait for it to charge. Set it to TTL or manual, then check that the camera shows the flash as ready.
- Test: take one shot and check the review image. If the subject is dark or bright, adjust the flash before shooting more.
Fill flash outdoors
Fill flash is one of the most useful first techniques. In bright sun, a face in shade can look dark against a bright background. The flash lifts the shadows on the subject while the background keeps its natural exposure.
Start with the flash about one to two stops below the ambient exposure. Use flash exposure compensation or a lower manual power to set that.
Bounce flash
Bounce flash means tilting the speedlight head toward a white ceiling or wall, so the light spreads out and arrives at the subject from above and to the side. The result is softer than direct flash.
Bouncing costs power. It typically loses two to three stops or more compared with direct flash, and higher ceilings cost more. The bounced light also takes on the color of the surface, which can add a yellow or orange cast. See bounce flash color cast for causes and fixes.
Off-camera flash
Moving the flash away from the lens changes where shadows fall, and that can add shape to a face. Off-camera flash needs a trigger, either a cable or a radio trigger. Once you have one light working, you can add a second. The basic roles and setup order are in multiple off-camera flash techniques.
Specialist flash: ring and high-speed
Two specialist uses are worth knowing about early, even if you don’t need them yet:
- A ring flash surrounds the lens and gives frontal light with a distinctive halo shadow. It’s popular for portraits. See ring flash for portraits.
- High-speed flash uses a very short flash burst to freeze fast motion. It’s a different goal from high-speed sync, which lets you shoot faster than the normal sync speed. See high-speed flash photography.
A simple first setup
A useful first kit is one speedlight, one radio trigger if you plan to shoot off-camera, and one modifier such as a white umbrella or a 60–90 cm softbox. Work through it like this:
- Turn the flash off and set your camera for the ambient exposure you want.
- Turn the flash on, set manual power to a middle value such as 1/8 or 1/16, and take a test shot.
- Adjust power or distance until the subject looks right, then check a few frames.
Once that works, try the same setup with the flash off the camera. Watch how each change moves the shadows on the face.
If the flash looks too strong on the face, consider how the light is shaped. Our article on why flash often looks flattering covers the trade-offs.
Safety
- Don’t fire a flash at close range into the eyes of infants or at drivers or pilots.
- Speedlights heat up when fired at full power many times in a row. Let them cool.
- Never open a flash unit. Its capacitors can hold a dangerous charge.
- Avoid repeated direct flash close to people with photosensitive epilepsy.
Where to go next
Start with the basics of TTL and manual modes, then practice fill flash outdoors. Move on to bounce and off-camera flash once the first setup feels predictable. If you want a specific technique, the spoke articles on this site each cover one subject in depth, including the balancing guide and TTL vs manual.