Off-camera flash lets you choose where the light comes from. Once you use more than one light, you can shape the subject, separate it from the background, and control how much contrast the photo has. This article covers the light roles, the order to build a setup, and the controls that keep several flashes from working against each other.
Why use off-camera flash?
Off-camera flash isn’t always better than flash on the camera. Its main advantage is that you can move the light away from the lens. That changes where shadows fall, which gives the face and body more shape. A flash placed on the camera tends to flatten the subject. Moving it to the side also reduces the chance of red-eye.
The costs are real. You need extra gear, such as stands, modifiers, and a trigger system. You also have more settings to manage, and more ways for the setup to go wrong. For a single subject, one off-camera light is often enough.
The four light roles
Most multi-light setups use some combination of four roles, an extension of classic three-point lighting:
- Key light. This is the main light. It sets the shape and mood of the subject. A common starting point is about 45° to one side of the subject and a little above eye level.
- Fill light. This softens shadows on the side away from the key. It can be a second flash, but a reflector often does the job.
- Rim or hair light. This sits behind the subject, opposite the key, and separates the edges from the background. It’s often set somewhat brighter than the key.
- Background light. This lights the backdrop on its own. The subject needs to be a few meters in front of the background so the background can fall darker.
Build the setup one light at a time
Adding several lights at once makes it hard to see what each one is doing. Build the setup in this order:
- Turn off every light except the key. Set its position and power until the subject looks right.
- Add the fill light and check the key and fill together.
- Add the rim light and check the effect on the edges.
- Add the background light last, then review the full setup.
Test each light on its own as well, either with a flash meter or with a test shot. This makes it easier to find which light is causing a problem.
Lighting ratios
The lighting ratio compares the key with the fill. A few common ratios:
- 2:1 is a one-stop difference between key and fill.
- 4:1 is a two-stop difference.
- 8:1 is a three-stop difference.
A lower ratio gives softer, flatter light. A higher ratio gives more contrast. The ratio is a guide, not a rule, so pick the one that suits the look you want.
Triggers, groups and channels
Radio triggers are the usual way to fire several off-camera flashes. Two settings are easy to confuse:
- A channel is a radio frequency. Every flash and the trigger must be on the same channel to communicate.
- A group is a set of flashes that you control together, such as group A or group B. Many radio systems offer several groups, commonly A to E.
Each group can be set to TTL or manual. This lets you run a TTL key and a manual rim light, for example. For more on that choice, see TTL vs manual flash.
Triggers generally work only with flashes from the same brand. Don’t assume that mixing brands will work, and check compatibility before buying.
Optical slaves and the TTL pre-flash
An optical slave is a cheap sensor that fires a flash when it sees light from another flash. It doesn’t need a radio link.
When the master flash uses TTL, it fires a pre-flash just before the main burst. A slave that sees the pre-flash can fire too early, which ruins the exposure. Many slaves have a setting that ignores the pre-flash, often labeled S2. Set the slave to that mode when the master uses TTL.
Controlling spill
Light spreads, and extra light on the backdrop or the wrong part of the subject can spoil the image. A few tools limit spill:
- Grids narrow the beam. Grid angles of roughly 10° to 40° are common.
- Snoots focus a small beam on one area.
- Flags and black cards block light from reaching the lens or the background.
- Gels change the color of a single light, such as a background light.
Set the camera white balance around daylight (about 5500 K) for flash. If you use gels, make sure they match across all the lights, or the colors will drift.
Two key-height lights produce double catchlights and two nose shadows, which usually looks unnatural. Avoid that arrangement unless you want the effect.
Multi mode on Godox (what it means)
Many Godox speedlights have a multi mode, also called stroboscopic mode. In this mode, one exposure captures several flash bursts in sequence. You set the power, the number of flashes, and the firing frequency in hertz. Labels and ranges differ between models, so check your flash’s manual before you use it. For more on flash used to freeze motion, see high-speed flash photography.
Common mistakes
- More lights isn’t always better. Extra lights can flatten the subject and add competing shadows.
- Groups and channels aren’t the same. A channel is a radio frequency. A group is a set of flashes controlled together.
- Mixing brands often means the triggers don’t communicate at all.
- Ignoring the ambient light. Set the ambient exposure first so the flashes aren’t competing with the room light. The steps are in balancing flash and ambient light.
Safety
- Sandbag light stands, especially when you use umbrellas or softboxes outdoors. Wind can knock them over.
- Tape down cables and stand legs in walkways so people don’t trip over them.