Catalog product shots have a different job from a single hero image. Every photo in a range needs to look like it was taken in the same place, with the same light and the same sharpness, so shoppers can compare items side by side. This guide covers the lighting choices that make that possible. Specialty setups for individual products link out to their own guides.
Start with source size: hard and soft light
How hard a light looks depends on the size of the source relative to the product, and on its distance. A small or distant source gives crisp edges and dense shadows. A large source placed close gives soft, wrapping light. Doubling the distance between the light and the product cuts the light to a quarter of what it was, which is the inverse square law at work and a two-stop change.
Soft light is not always the better choice. Hard light brings out texture, glass edges, and metal detail, and it suits bold styles. A bare reflector, a fresnel, a snoot, or a grid on a light gives hard light. A bare speedlight placed at a distance does the same job.
Set up a hard-light product shot
A common hard-light layout puts the key light at about 45° to the side of the product, or slightly behind it. A strip box adds a clean edge highlight. A white fill card on the opposite side lifts the shadow side, and black flags add negative fill where you want shadows deeper.
Start with one or two sources and some cards before you add more lights. Most products need one to three sources. Extra lights tend to add flare and competing shadows rather than better detail. For softer shadow control, see shadow control for product photos.
Control reflections before they start
A reflection follows the angle of incidence equals the angle of reflection rule. If the light sits in the direction the camera looks at a glossy surface, the light shows up in the lens. Move the light out of that angle, or move the camera. On glossy products, a very large diffused source gives a smooth, even reflection instead of a hotspot.
For specular reflections on glass or polished surfaces, cross-polarization works well. Put a polarizing gel on the light and a polarizer on the lens. This costs several stops of light, often 3 or more, because both the gel and the lens filter absorb light. A circular polarizer on the lens alone reduces reflections from non-metal surfaces such as glass and paint, but it does little for bare metal under ordinary light. For glass-specific setups, see lighting glassware, and for metal and chrome, see how to photograph something reflective.
Camera settings for sharp, repeatable images
Shoot at your camera’s base ISO, usually 64 to 100. Use a tripod and shoot RAW. Products do not move, so you can add light or use a slower shutter instead of raising ISO.
For most products, apertures between f/8 and f/16 work well. Diffraction starts to soften detail somewhere around f/11 to f/16, depending on the sensor, so stopping down further does not always make an image sharper. When f/11 cannot keep a deep product sharp from front to back, use focus stacking: shoot a series of frames with the focus point moved in small steps, then blend them. Stacks often run from 5 to 30 frames or more.
With strobes, set the shutter at or below the flash sync speed, often about 1/160 to 1/250 s, so room light does not show up in the frame. Tethering the camera to a laptop or tablet lets you check each frame at full size.
Lock the settings for consistency
A catalog looks like a catalog when every product shares the same look. Use manual exposure, set a custom white balance from a gray card or color checker, and mark the positions of the lights and the product with tape. Shoot a gray card or color checker at the start of each session. Auto white balance shifts from frame to frame, which breaks the match.
Keep a short note of your settings and light positions for each product set. When a new batch arrives weeks later, you can rebuild the same setup from the note rather than guessing.
Check the light source
Continuous LED panels are useful for color-critical work when their CRI or TLCI is 95 or higher. Budget LEDs do not always match their stated CRI, and cheap PWM dimming can cause banding in video and at fast shutter speeds. Test a sample light before buying a set.
Specialty setups
Different products need different light:
- White background product shots need the background lit separately from the product.
- Jewelry needs soft light for metal and small hard points for stone sparkle.
- Cosmetics and packaging need strip lights, backlit liquids, and careful reflection control.
- Flat lays need an overhead camera and side light.
- Apparel needs raking light for texture and even light for color.
Starting on a budget
A light tent or light box can handle small items on a white background without a full studio. Photography light tents explain how to size one and set up external lights, and are photo light boxes worth it? covers the trade-offs.
Marketplace main images
Many marketplaces ask for a pure white main image, with the product filling most of the frame and no overlays. Requirements change, and each platform sets its own minimum image size, so check the current seller guidelines before you shoot. Shoot at a large size so zoom features stay sharp.
Still life at home
You do not need a studio for still life. Indirect window light is the best free source, and a north-facing window is often recommended in the Northern Hemisphere because it gives soft, steady light. Place a white foam board on the shadow side to lift shadows, and use a black card to shape the light where you want it deeper. Shoot on a tripod and follow the same steps as in a studio.
Common misconceptions
- Soft light is not always better. Hard light suits texture, glass edges, and bold styles.
- f/22 is not the sharpest setting. Diffraction softens the whole image.
- More lights do not mean better results. Most products need one to three sources plus cards.
- Auto white balance breaks catalog consistency.
- A polarizer does not remove reflections from bare metal unless the light is also polarized.
Safety
Modeling lamps and continuous hot lights get very hot, so keep them away from diffusion fabric, paper, and props. Sandbag every light stand, especially booms. Strobe capacitors can hold a charge after the unit is switched off, so do not open flash heads.
Pick the setup that suits the product, get the light right, then lock it down. The specialty guides above take that approach to individual products.