Product and Food Lighting

How to avoid reflections in photography?

Avoid reflections in photography by changing your angle, diffusing the light, using a circular polarizer, and shooting through glass cleanly, with practical product tips.

On this page
  1. Change the angle
  2. Diffuse and move the light
  3. Use a circular polarizer
  4. Shooting through glass
  5. Framed art and eyeglasses
  6. Glossy products
  7. Hide your own reflection
  8. Phone tips
  9. Common misconceptions
  10. Safety

Reflections ruin a shot when they bounce a light, a room, or the photographer into the frame. The fix is usually geometry: move the light, the camera, or the subject until the reflection misses the lens. For glossy items, use a large, diffused source. For non-metal surfaces, a circular polarizer helps. Those three steps handle most cases.

Change the angle

A reflection follows one rule: the angle of incidence equals the angle of reflection. If the light arrives from the same direction the camera looks at a surface, the light bounces straight into the lens. Shoot slightly off-axis, to the left, right, above, or below, instead of straight on. A common starting point is to set the light and the subject at about 45°, so the reflected light travels away from the camera.

Diffuse and move the light

A small, bright source makes a sharp, bright reflection. A large, diffused source makes a smooth, even one that is much easier to live with. Use a softbox, a diffusion scrim, or a window instead of direct sun or a bare bulb. Turn off the on-camera flash, or reposition an off-camera flash, because a direct flash fires straight back into anything shiny. Repositioning often works better than switching the flash off entirely.

Use a circular polarizer

A circular polarizer on the lens cuts reflections from non-metal surfaces such as glass, water, paint, and leaves. Rotate it while you look through the viewfinder, and you will see the reflection strengthen or fade. It works best when the reflection angle is near Brewster’s angle, about 53° for water and 56° for glass, measured from the surface’s perpendicular.

A polarizer has limits:

  • It does not remove every reflection. It adjusts them.
  • It costs about 1.5 to 2 stops of light.
  • It barely affects bare metal or polished chrome under ordinary light. For metal, you need polarized light on the subject as well (cross-polarization). How to photograph something reflective covers other options for metal.

Shooting through glass

Reflections through windows and display cases come from the bright side of the glass, which is often your side. Three fixes help:

  • Press the lens against the glass. A rubber lens hood helps you do this without scratching it. Closing the gap stops the room from reflecting into the frame.
  • Drape a dark cloth or hold a black card with a lens hole around the lens.
  • Darken your side. Turn off interior lights on your side and wear dark clothing.

Framed art and eyeglasses

For framed art, place two lights at about 45° on each side of the artwork, with the camera centered and square to the frame. Keep the room dark on your side.

For eyeglasses, raise the light, move it farther to the side, or tilt the frames slightly down at the ears. Anti-reflective coatings still show faint green or purple reflections, which are hard to remove completely.

Glossy products

A very large diffused source gives a smooth, even reflection that reads as shine rather than as a hotspot. Some photographers use a dulling spray on the product to reduce gloss. Do not use it on items you will sell unless you can clean it off, and use the spray in a well-ventilated space.

Hide your own reflection

Your camera and your clothing can show up in a reflective surface. Use a black card with a lens hole, or a longer focal length from further back, to keep the camera out of the reflection.

Phone tips

On a phone, tap the brightest part of the scene to set exposure there, then slide the exposure down so the reflection darkens. Use a 3 to 5 second timer to keep the shot steady.

Common misconceptions

  • A polarizer does not remove every reflection. It depends on the angle and the surface.
  • Polarizers do not work on chrome or polished metal under normal light.
  • Turning off the flash is not always the fix. Repositioning an off-axis flash often works better.
  • Reflections are not always flaws. Controlled highlights show shape and gloss.

Safety

Dulling sprays are aerosols. Use them with good ventilation and keep them away from heat sources.

For glass-specific setups, see lighting glassware and stopping reflections. For the wider product lighting approach, see product photography lighting.

The complete guide to product and food lighting

Product Photography Lighting: Advanced Techniques for Catalog-Quality Shots
Read the guide

Keep exploring

Guides from other topics

All topics →