Product and Food Lighting

Lighting Clothing and Fabric Texture for Apparel Photos

Light clothing and fabric texture: low raking side light for weave and knit, even light for accurate color, and tips for satin, velvet, black and white garments.

On this page
  1. Why light changes fabric
  2. Raking light setup
  3. Even base light
  4. Fabric by fabric
  5. Black and white garments
  6. Color accuracy
  7. Moiré on fine weaves
  8. Ghost mannequin, flat lay, and on-model
  9. Prepare the garment
  10. Keep the set consistent
  11. Common mistakes
  12. Safety

Fabric shows its texture under low, raking light, and its true color under even, soft light. A good apparel setup uses both: a low side light to bring out weave, knit, and nap, and a broader light to keep the colors honest. The right balance depends on the fabric, so the guide below goes fabric by fabric.

Why light changes fabric

A weave or knit is made of small ridges and fibers. Light that falls across them at a low angle casts tiny shadows and shows the pattern. Light that falls straight on fills those shadows in and flattens the surface. Soft frontal light also hides wrinkles, which can make a garment look better than it is, but it also hides the texture the shopper wants to see.

Raking light setup

Place a light low and to the side, roughly 60 to 80° off the camera’s axis. This is the setup for showing texture. It works best on knits, wool, denim, and tweed. A strip light placed at the side gives the most controlled raking light.

Even base light

To keep the color even, add two softboxes at about 45° on either side of the garment. The softboxes give the overall exposure and the color, and the raking light adds texture on top. For on-model shots, a large octabox key often serves as the base light.

Fabric by fabric

  • Knits, wool, denim, and tweed: benefit most from side light. Smooth cottons need less.
  • Satin and silk: use large soft sources for smooth gradients. Small sources cause hot spots on the sheen.
  • Velvet and suede: change tone with the angle of the light. Test a few angles, and keep the angle the same across a set.
  • Sequins and metallics: add a small, hard source to create sparkle. Keep it off the fabric’s matte areas.

Black and white garments

Black garments need more light, or about +0.5 to +1 stop of exposure, to hold detail in the fabric. Avoid crushing the blacks in post, or the texture disappears. White garments need protected highlights. Use black cards at the edges to give a white garment its shape against a white background.

Color accuracy

Color matters for returns. Use lights with a CRI or TLCI of 95 or higher, set a custom white balance from a gray card, and shoot a color checker at the start of each session. Check the photo against the physical item in the same light, and fix any color shift before you process the set.

Moiré on fine weaves

Fine patterns can produce moiré, a rippling pattern that is not in the fabric. This is more common on sensors without an anti-aliasing filter. Change the distance, the angle, or the focal length, or stop down slightly, and check again.

Ghost mannequin, flat lay, and on-model

Each shoot type needs a different setup. A ghost mannequin shot focuses on the shape of the garment. A flat lay shows the whole piece with the raking light set low across the surface. An on-model shot needs a larger, flattering key and more care with the model’s skin tone and posture. For flat lays, see flat lay photography lighting.

Prepare the garment

Steam the garment before the shoot. Raking light shows every wrinkle, so steaming saves time in post. Retouching wrinkles is slower than steaming, and it is hard to make the result look natural.

Keep the set consistent

Lock the exposure, the white balance, and the light positions for every garment in a set. Auto white balance drifts between shots and misrepresents the color. Tape-mark the positions so the next session matches.

Common mistakes

  • Brighter is not better for texture. The angle of the light matters more than its power.
  • Fully shadowless light makes fabric look flat and cheap.
  • Auto white balance drifts and misrepresents the color of the garment.
  • Retouching can fix wrinkles, but steaming before the shoot is faster and looks more natural.

Safety

Keep steamers and hot lights away from fabric. Steam and hot lamps can burn hands and scorch the garment.

For the overhead layouts that suit folded or flat clothing, see flat lay photography lighting. For the general approach to soft light, see shadow control for product photos.

The complete guide to product and food lighting

Product Photography Lighting: Advanced Techniques for Catalog-Quality Shots
Read the guide

Keep exploring

Guides from other topics

All topics →