Product and Food Lighting

Lighting Glassware and Stopping Reflections in Tabletop Photography

Light clear glassware with bright-field or dark-field setups, control reflections with angle and polarizers, and build tabletop props that look real in the photo.

On this page
  1. Choose bright-field or dark-field
  2. Bright-field in practice
  3. Dark-field in practice
  4. Strip softboxes for vertical highlights
  5. Control reflections
  6. Hide the camera
  7. Tabletop surfaces
  8. Drinks and props
  9. Lens and aperture
  10. Common misconceptions
  11. Safety

Clear glass is hard to photograph because it has no color of its own. It shows up through what it refracts and reflects: its edges, the light passing through it, and whatever is around it. This guide covers the two main lighting approaches, how to keep reflections under control, and the tabletop details that make a glass or a drink look right.

Choose bright-field or dark-field

Two basic setups cover most glassware:

  • Bright-field: a light background, such as a backlit diffusion panel or a white card, with black cards just outside the frame on both sides. The glass shows dark edges against a bright background.
  • Dark-field: a black background with a large light behind the glass. A black card, smaller than the light, placed centered behind the glass blocks the middle of the light, so the light wraps only the edges. The glass then shows bright outlines.

Bright-field suits clear glass that should look clean and bright, such as water glasses and product bottles. Dark-field suits glass that should look dramatic, or glass that sits on a dark surface.

Bright-field in practice

Start with the background. Place a diffusion panel or a white card a short distance behind the glass and light it from behind. Then place black cards just outside the frame on each side. These cards create the dark edge lines, so their position matters more than the light’s power. Move them in until the edges darken without covering the glass itself.

Dark-field in practice

Use a black background and a large light behind the glass. The black card behind the glass should be smaller than the light, so the light wraps only around the edges. Adjust its size and position until the outline is clean. This takes some trial and error, but a few test frames usually get it right.

Strip softboxes for vertical highlights

A strip softbox placed beside the glass gives clean vertical highlight lines along its sides. Keep the strip narrow and place it so the highlight sits on the edge of the glass rather than across the middle.

Control reflections

Reflections follow one rule: the angle of incidence equals the angle of reflection. Keep lights out of the angles that reflect into the lens.

A circular polarizer on the lens reduces reflections from glass. It works best when the reflection angle is near Brewster’s angle, which is about 56° from the perpendicular for ordinary glass. It does not remove every reflection at every angle, and it costs about 1.5 to 2 stops of light. Rotate the filter while you look through the viewfinder to see the effect.

Some reflections help show shape. A controlled highlight on the glass tells the viewer it is glass. Aim for control rather than total removal.

Hide the camera

The camera itself often shows up in glass. Use a black card with a hole cut for the lens, or wear dark clothing if you are standing close. A longer lens, around 90 to 150 mm on a full-frame body, shot from further back reduces perspective distortion and cuts how much of the room the glass reflects.

Tabletop surfaces

Black or white acrylic gives a mirror-like base reflection. Backlit white acrylic gives a glowing base that works well for drinks. Choose the surface before you set the lights, because it changes how the base reflects.

Drinks and props

Dark drinks such as cola, whisky, and red wine block a lot of light. Dilute them with a little water so backlight can pass through the liquid. Test the color before the session, because it changes with the dilution.

For condensation, spray a 50/50 mix of glycerin and water on the outside of the glass. It lasts longer than plain water. Acrylic ice does not melt during long sessions, which helps when the glass needs to look cold for hours. Handle every prop with gloves to avoid fingerprints.

Lens and aperture

Shoot at about f/8 to f/16 at tabletop distances. Focus stacking helps with tall stems and stacked glasses, where a single focus plane cannot cover the whole subject from front to back.

Common misconceptions

  • Front lighting usually makes glass look flat and shows hot spots. Glass is defined by backlight and edges.
  • A polarizer is not a universal fix. It barely changes some reflection angles.
  • More light does not help. Control of the black and white areas matters more than power.
  • Reflections are not always bad. Controlled highlights show shape and gloss.

Safety

Chipped glassware can cut. Inspect props before each session and discard any piece with a chip or crack.

For a general approach to reflections beyond glassware, see how to avoid reflections in photography. The product photography lighting guide covers the wider set of techniques, and how to photograph something reflective covers metal and other shiny products.

The complete guide to product and food lighting

Product Photography Lighting: Advanced Techniques for Catalog-Quality Shots
Read the guide

Keep exploring

Guides from other topics

All topics →