Every flash photo has two exposures: the ambient light already in the scene and the light from the flash. Getting them to work together is mostly a matter of setting each one separately. The core rule is simple. Shutter speed controls the ambient light, and flash power and distance control the subject. Aperture and ISO affect both.
The core rule
- Shutter speed controls the ambient exposure, as long as you stay at or below the flash sync speed.
- Flash power and distance control how much light the flash adds to the subject.
- Aperture and ISO affect both the ambient and the flash exposure.
Because the flash burst is so short, changing shutter speed (below sync) doesn’t change the flash contribution. This makes the two exposures easier to control separately.
Step 1: set the ambient exposure first
Start with the flash off, so you can see the scene as the camera does.
- Set the camera to manual mode.
- Choose ISO and aperture for the depth of field and noise you want.
- Adjust the shutter speed until the background looks the way you want. A faster shutter gives a darker background, and a slower shutter brings in more of the room or the sky.
- Lock these settings. Don’t change them when you add the flash.
Many photographers underexpose the background by about one to two stops for a moody look. For a dramatic dark background, the underexposure may be three stops or more.
Step 2: add the flash for the subject
Turn the flash on in manual power, or in TTL with flash exposure compensation.
- Take a test shot.
- If the subject is too bright, turn the power down or move the flash further away.
- If the subject is too dark, turn the power up or move the flash closer.
- Repeat until the subject looks right. The background shouldn’t change, because you set it in step 1.
Step 3: match direction and color
Once the exposure works, check the direction and color of the light.
- Direction. Place the flash so it comes from roughly the same side as the main ambient source, such as a window or the sun. This keeps the light looking natural.
- Color. Daylight-balanced flash (about 5500 K) matches daylight well. Indoors, a warm tungsten room will look different. Gels can help, as explained below.
Fill flash in bright sun
Fill flash is a common case in full sun. The subject is in shadow, and the background is bright.
- Set the camera for the background exposure, as in step 1.
- Turn the flash on and set it one to two stops below the ambient exposure, using flash exposure compensation or a lower manual power.
- Check the face. The shadows should lift, but the flash shouldn’t look like the main light.
Keep the fill lower than the ambient light. A fill that matches the ambient exposure usually looks flat and unnatural.
Sync speed limits: HSS, ND and slow sync
Most cameras have a maximum flash sync speed, often between 1/160 and 1/250 s depending on the body. At faster speeds, part of the frame can go dark, which shows as a band across the image.
You have three main options when you need a faster shutter:
- High-speed sync (HSS) pulses the flash during the exposure so you can shoot faster than sync speed. It costs roughly one to two stops of effective flash power or more, and it reduces the flash’s range.
- ND filters reduce the light from both the ambient and the flash by the same amount. You can open the aperture for shallow depth of field and stay at sync speed. Because both sources are reduced equally, the balance between them stays the same.
- Slow sync uses a slower shutter to bring in more ambient light. This works indoors, where you want the room to show. Rear-curtain sync fires the flash at the end of the exposure, so any motion trail falls behind the subject.
In aperture priority, some cameras choose a very slow shutter speed when flash is on. Check your camera’s setting for flash sync speed in aperture priority mode. Canon and Nikon both have options for this, though the names and ranges vary.
Color with mixed light
Warm ambient light can clash with daylight-balanced flash. You can match them in two ways:
- Gel the flash with a CTO (color temperature orange) gel, then set the white balance to tungsten to keep warm backgrounds neutral. A full CTO gel brings daylight-balanced flash roughly toward tungsten color. The exact result varies by brand.
- Use a partial gel, such as a 1/2 or 1/4 CTO, when you want some warmth to remain.
Gels reduce the flash output, so expect to adjust the power. For more on color cast from bounced light, see bounce flash color cast.
Common mistakes
- Faster shutter doesn’t weaken the flash below sync speed. The flash exposure stays the same, and only the ambient changes.
- Fill flash doesn’t need to match the ambient light. It usually sits one to two stops under.
- TTL exposes the subject, not the background. It doesn’t balance the ambient light for you. Set the background first.
- HSS isn’t free. It costs power and range, so plan for it.
For a faster way to set up multiple lights, see multiple off-camera flash techniques. For the choice between TTL and manual, see TTL vs manual flash.
Quick reference
| Setting | What it controls | Notes |
|---|---|---|
| Shutter speed | Ambient light | Keep at or below sync speed to keep the flash exposure unchanged |
| Flash power or distance | Flash on the subject | Halve the power for one stop less, or double the distance for two stops less |
| Aperture | Both ambient and flash | Wider aperture adds more of both |
| ISO | Both ambient and flash | Higher ISO adds noise |
| Flash exposure compensation | Flash only | Usually ±3 stops in third-stop steps |
| ND filter | Both ambient and flash | Lets you use a wider aperture at sync speed |