Lighting Fundamentals

Lighting Ratios in Photography: What 1:1, 2:1 and 4:1 Mean for Your Portraits

A lighting ratio compares the lit side of a face with the shadow side. Learn what 1:1, 2:1, 3:1, 4:1 and 8:1 look like and how to measure them.

On this page
  1. Ratios and stops
  2. What each ratio looks like
  3. Measure a ratio with an incident meter
  4. Change the ratio
  5. Ratio is not the same as quality
  6. Ratios in a three-light setup
  7. Counting conventions
  8. Common misconceptions

A lighting ratio compares the brightness of the lit side of the subject with the shadow side. A 1:1 ratio means both sides are equally bright. A 2:1 ratio means the lit side is twice as bright, which is one stop of difference.

Ratios and stops

Each stop doubles the ratio. Use this table:

Difference Ratio
0 stops 1:1
1 stop 2:1
1.5 stops about 3:1
2 stops 4:1
3 stops 8:1

Because a meter reads in stops, it’s usually easiest to measure the difference in stops first and then convert it to a ratio.

What each ratio looks like

  • 1:1 is flat and shadowless. It suits beauty work, clamshell lighting, high-key images and products.
  • 2:1 gives subtle modeling. It’s flattering for most faces and common in commercial headshots.
  • 3:1 is the classic portrait standard. It gives a clear shape and open shadows.
  • 4:1 is dramatic and moody, and it suits strong character portraits.
  • 8:1 and above is low-key, film-noir territory. The shadow side is nearly black.

Measure a ratio with an incident meter

An incident meter reads the light falling on the subject, so it’s the most direct way to measure a ratio:

  1. Point the dome toward the key light and note the f-stop.
  2. Point the dome toward the fill light, or block the key and point the dome at the shadow side. Note that f-stop.
  3. Compare the two. The difference in stops gives the ratio.

For example, if the key reads f/8 and the fill reads f/4, the difference is two stops, so the ratio is 4:1. For meter basics, see how light is measured.

Change the ratio

You can change the ratio in four ways:

  • Fill power. A weaker fill raises the ratio. A stronger fill lowers it.
  • Fill distance. Under the inverse square law, moving the fill farther away reduces its effect.
  • Reflector type. A white reflector gives a modest fill, and a silver one gives more. The exact ratio depends on distance and angle.
  • Negative fill. A black flag or card takes light away from the shadow side and deepens the shadows.

Ratio is not the same as quality

The ratio describes the brightness difference between the two sides. Quality describes how hard or soft the light is, which depends on the size of the source. The two are separate controls. Soft light can have an 8:1 ratio, and hard light can have a 2:1 ratio. For more on quality, see hard light vs soft light.

Ratios in a three-light setup

In a three-point setup, the fill light typically sits 1 to 2 stops below the key. That’s a ratio of 2:1 to 4:1. A reflector can do the same job.

Counting conventions

Not all sources count ratios the same way. Some count the key and fill together on the lit side, so a key one stop above the fill might be described as 3:1. When you write or discuss a ratio, say which convention you’re using, so readers and clients aren’t confused.

Common misconceptions

  • A 2:1 ratio doesn’t mean the fill has half the key’s power. The ratio describes the light measured at the subject.
  • Higher ratios are not better or more professional. Choose the ratio for the subject and mood.
  • You can’t reliably judge a ratio by eye on a camera screen. Measure with a meter, or check the histogram.

The complete guide to lighting fundamentals

Photography Lighting Techniques: How Light Shapes Every Photo
Read the guide

Keep exploring

Guides from other topics

All topics →