DIY Lighting

How to Build a DIY LED Panel for Continuous Photo Light

Build a DIY LED panel for photo and video. Covers high-CRI strips, heat sinking, power headroom, flicker-free dimming, diffusion and batteries.

On this page
  1. What a photo LED panel needs
  2. Parts list
  3. Choosing the LEDs
  4. Layout and wiring
  5. Bicolor option
  6. Heat and mounting
  7. Power supply sizing
  8. Dimming and flicker on camera
  9. Diffusion and control
  10. Battery option
  11. Common mistakes
  12. Safety

What a photo LED panel needs

A panel for photography is different from a home lighting fixture. It needs four things:

  • Color accuracy. Look for CRI 90 or higher, and 95 or higher if your budget allows. Lumens alone do not make a panel suitable for portraits.
  • Heat sinking. LED strips lose brightness and shift color when they run hot.
  • Even output. Rows of LEDs behind a diffuser give smooth light without visible dots.
  • Flicker-free dimming. A dimmer that flickers will show up as bands on camera.

If you need a smaller, lower-cost continuous light, a DIY tube light is another option.

Parts list

  • Base. An aluminum sheet or aluminum composite panel, for example 30 × 30 cm. The metal doubles as the heat sink.
  • LEDs. A high-CRI 2835 strip at 120 LEDs per meter, or a COB strip, in 12V or 24V.
  • Power supply. A certified, enclosed DC supply rated 20 to 25% above the load.
  • Wire. 18 AWG wire handles a few amps at 12V over short runs.
  • Diffuser. 3 mm opal acrylic or rip-stop nylon.
  • Mount. A 1/4”-20 or 3/8”-16 threaded insert and a ball head.

Choosing the LEDs

  • Pick high CRI. A 90 or higher rating is the minimum for portrait work.
  • Pick the density. A 2835 strip at 120 LEDs per meter gives a smooth light. Power draw varies by product, and 2835 strips at this density often draw roughly 10 to 20 watts per meter. Check the datasheet.
  • Choose 12V or 24V. A 24V system draws about half the current of a 12V system for the same power, so voltage drop is smaller. Use 24V for long runs.

Layout and wiring

  • Row spacing. Leave about 1 to 2 cm between rows for even coverage.
  • Parallel rows. Wire each row from a common bus, not as one long series run.
  • Long runs. Voltage drop grows with run length. For runs of 5 meters or more, feed power from both ends, or use 24V.

Bicolor option

You can alternate warm rows (about 2700 to 3200K) with cool rows (about 5600 to 6500K). A two-channel dimmer then lets you mix between them. Wire the warm rows to one output of the dimmer and the cool rows to the other, and wire the rows in parallel as described above.

Heat and mounting

Attach the strips to the aluminum base with adhesive or clips rated for the strip. Good contact with the metal carries heat away from the LEDs. Poor heat sinking shortens the life of the LEDs and shifts their color.

Power supply sizing

Add headroom. Choose a supply rated 20 to 25% above the panel’s load. For example, a 60 W panel needs a supply of at least 75 W. Adding more strip to a supply that is already near its rating will cause problems, and voltage drop limits how far you can scale one supply.

Dimming and flicker on camera

  • Look for dimmers that use high-frequency PWM, several kHz or higher, or constant-current dimming for video.
  • Not every dimmer is flicker-free on camera.
  • Test before a shoot. Take a test frame at your planned shutter speed, both at full output and at the dimmed level, and check for bands.

Diffusion and control

Place the diffuser about 1 to 3 cm in front of the LEDs. Opal acrylic or rip-stop nylon both work. Black foam board barn doors help control spill and keep light off the background.

Battery option

A V-mount battery is 14.4V nominal and 16.8V fully charged. A 12V panel needs a buck converter to step the voltage down. Check the converter’s input voltage range before you buy it, because it must handle the full 16.8V. Fuse the battery lead close to the battery.

Common mistakes

  • Skipping heat sinking. LED strips need a good thermal path.
  • Judging a panel by lumens alone. CRI and flicker matter as much.
  • Assuming any dimmer is flicker-free on camera. Test it first.
  • Adding strip to a supply without checking its rating. Overloading it shortens its life and can cause failure.

Safety

  • Use a certified, enclosed power supply. Leave mains-side wiring to a qualified person.
  • Fuse the battery lead close to the battery.
  • Insulate all solder joints. Aluminum panels are conductive, so keep wiring away from the metal or insulate it.

The complete guide to diy lighting

DIY Photography Lighting: Homemade Ideas That Work
Read the guide

Keep exploring

Guides from other topics

All topics →