DIY Lighting

How do I make a homemade ringlight?

Make a homemade ringlight with a 12 to 14 in hoop, a CRI 90+ 12V LED strip, a DC adapter and diffusion. Takes about an hour, with a phone version too.

On this page
  1. Short answer
  2. What you need
  3. Steps
  4. Adhesive alone will not hold
  5. Phone version
  6. Heavier alternative: a bulb ring
  7. Cost and time
  8. Limits to expect
  9. Common mistakes
  10. Safety

Short answer

To make a homemade ringlight, wrap a self-adhesive 12V LED strip with a CRI of 90 or higher around a 12 to 14 inch hoop or cardboard ring. Connect it to a 12V DC adapter, add a diffuser over the front, and mount the ring on a stand. Shoot through the center. A basic build takes about an hour and costs roughly $15 to $30, though prices vary.

What you need

  • A 12 to 14 inch ring. An embroidery hoop, a cut cardboard ring or a plywood ring all work.
  • About 1 to 1.2 meters of 12V LED strip, CRI 90+. The strip length is pi times the ring diameter. A 12-inch ring needs about 0.96 meters.
  • A 12V 2A DC adapter with a barrel-jack connector.
  • An inline dimmer (optional).
  • Diffusion: parchment, frosted plastic or white fabric.
  • Zip ties, glue, isopropyl alcohol and a clean cloth.

Steps

  1. Measure the circumference. Multiply the ring’s diameter by pi, and cut the strip only at the marked cut points.
  2. Clean the ring. Wipe the surface with isopropyl alcohol so the adhesive sticks. Let it dry.
  3. Stick the strip on the front face. Place it so the LEDs face the subject.
  4. Connect the power. Attach the barrel jack and the dimmer if you use one. Match the + and − polarity. Plug in and check that every LED lights before you add the diffuser.
  5. Add the diffuser. Wrap parchment, frosted plastic or white fabric over the strip to hide the individual LEDs.
  6. Secure and mount. Add zip ties or a bead of glue so the strip stays put. Clamp the ring to a light stand or tripod.

Adhesive alone will not hold

The self-adhesive backing can peel off over time, especially on fabric or cardboard. Add zip ties through the ring or a line of glue along the strip to keep it in place for the long term.

Phone version

For a phone, use a 5V USB strip powered by a power bank, and clamp a phone holder in the middle of the ring. A 5V strip gives much less light than a 12V strip, so it works best for close-range shots with a phone.

Heavier alternative: a bulb ring

You can also mount 4 to 8 small LED bulbs in sockets on a plywood ring. This gives more light than a strip, but the ring is heavier and the wiring is more involved. Use LED bulbs only.

Cost and time

Most builds cost roughly $15 to $30 in materials and take about an hour, depending on your skill and the parts you already have. Prices and times vary by region and by the parts you choose.

Limits to expect

  • A homemade ring is not as bright as a commercial 18-inch unit unless you use a high-density strip.
  • Cheap strips make skin look dull. Choose a strip with CRI 90 or higher.
  • A ring light casts a halo shadow on nearby backgrounds. Keep the subject some distance in front of the wall.

For the sizing, power and flicker details behind a larger build, see the DIY ring light guide.

Common mistakes

  • Buying any LED strip. Check the CRI first.
  • Relying on the adhesive alone. Add zip ties or glue.
  • Leaving the center too small. Leave at least 4 inches (10 cm) of opening for the lens.

Safety

  • Use a certified, enclosed DC adapter. Do not wire the strip to mains power.
  • Insulate any exposed solder joints with heat-shrink tubing.

The complete guide to diy lighting

DIY Photography Lighting: Homemade Ideas That Work
Read the guide

Keep exploring

Guides from other topics

All topics →