What a ring light does
A ring light surrounds the lens with light, so the subject is lit from almost straight on. The result is flat, nearly shadowless light and a round catchlight in the eyes. Ring lights suit beauty, product and video work, and close-up portraits where you want even light across the face.
Do ring lights work for photography? Yes, for the jobs above. They are not especially soft, though. The light is flat, so it does little to shape a face, and it can cast a halo shadow on a nearby background. If you want more modeling, add a side light or a softbox. The round catchlight also suits some portrait styles more than others.
If you want the quickest version, with an embroidery hoop and no spec sheet to read, see the homemade ringlight guide. This article covers the specs and power sizing behind a larger build.
Parts and ring size
- Ring base: an embroidery hoop, a cut ring of MDF, plywood or thick cardboard, or a large hula hoop.
- LED strip: 12V, 60 or 120 LEDs per meter, SMD 2835 or 5050, CRI 90 or higher.
- Power supply: a 12V DC adapter sized for the strip.
- Diffuser: frosted acrylic, white plastic or parchment.
- Mount: a 1/4”-20 bracket or a clamp for a light stand.
The opening in the middle has to clear your lens and any hood. A gap of about 4 to 6 inches (10 to 15 cm) is a common starting point. Commercial ring lights are often 10, 14 or 18 inches across. A larger ring makes a bigger light source, which gives softer light, but it needs more strip and more power.
The strip length is pi times the ring diameter. A 14-inch ring needs about 1.1 meters of strip.
Choosing the LED strip
- Pick CRI 90 or higher. Standard strips are often around CRI 80, which can make skin look dull or greenish.
- Use 12V, not 5V, for a ring this size. A 5V USB strip gives much less light.
- Choose 60 or 120 LEDs per meter. Denser strips give smoother light but cost more and draw more power.
- Consider a bicolor strip if you want to adjust color temperature. These strips usually run from about 3000K to 6500K, and need a two-channel controller.
Sizing the power supply
Power draw depends on the strip, so check its datasheet. A common 5050, 60-LED-per-meter, 12V strip is often listed at about 14 watts per meter (about 1.2 amps).
Add about 20% headroom. For example, a 1.1-meter strip at 14 watts per meter draws about 16 watts. With headroom, that is about 19 watts, so a 12V 2A supply (24 watts) fits well.
Wiring and connections
- Match the strip voltage to the supply. Connecting a 24V supply to a 12V strip can destroy it.
- Cut the strip only at the marked cut points.
- Solder the joints or use a proper connector, and match the + and − polarity.
- Insulate every exposed joint with heat-shrink tubing.
- Use an enclosed, certified DC adapter, not an open-frame mains supply.
Diffusion
Bare LEDs show as bright dots in the catchlights and can look harsh on skin. Diffuse the strip with frosted acrylic, white plastic, parchment or a white fabric. Leave a small gap between the strip and the diffuser so the dots blur. The exact gap depends on how densely the LEDs are spaced.
Dimming and flicker
Inline PWM dimmers can cause banding at fast shutter speeds or in video. Before you shoot, take test frames at your planned shutter speed and at your dimmed setting, and look for bands in the image. If you see them, use a different dimmer or keep the ring at full output and control the brightness another way.
Mounting and shooting
- Mount the ring on a stand with a 1/4”-20 thread or a clamp. The camera shoots through the center.
- Place the subject some distance in front of the background, so the halo shadow falls away from the subject.
- Have the subject look into the lens, so the ring’s reflection sits centered in each eye.
Limits and common mistakes
- A homemade ring is not as bright as a commercial 18-inch unit unless you use a high-density strip.
- Cheap strips make skin look dull. Check the CRI before you buy.
- Adhesive alone may not hold. Add zip ties or glue for a long-lasting ring.
- A ring light flattens the face. Add a side or back light if you want shape.
Safety
- Use a certified, enclosed DC adapter. Do not wire the strip to mains power.
- Insulate exposed solder joints.
- Keep the adapter away from heat, and do not cover it.