DIY Lighting

How to Make a DIY Softbox for Photography From Cheap Materials

Make a DIY softbox from foam board or cardboard with foil lining and a diffusion front. Learn placement at 45 degrees and how to use an LED bulb or speedlight.

On this page
  1. What makes a softbox soft
  2. Materials
  3. Build a foam board softbox
  4. Light source: LED or speedlight
  5. Grids and inner baffles
  6. Placement
  7. Cheap alternatives
  8. Stability
  9. Common mistakes
  10. Safety

What makes a softbox soft

A softbox is a box with a reflective inside and a diffusion panel at the front. The light is soft because the front panel is large compared with its distance from the subject. The box alone does not guarantee soft light. A softbox moved far away becomes a small, harder source.

A common rule of thumb for soft portrait light is to place the softbox about one diagonal width from the subject.

Materials

Part Options Notes
Body Cardboard box, about 18 to 24 inches across the front, or foam board panels taped into a tapered box Foam board holds its shape well
Interior Aluminum foil, silver mylar or an emergency blanket Glue it on with spray adhesive
Front diffuser White rip-stop nylon, a white shower curtain, parchment or tracing paper Each layer costs roughly one stop
Light An LED bulb in a socket, or a speedlight See the next sections

Build a foam board softbox

  1. Cut the panels. Cut four side panels, a back and a front to your chosen size. The front should be larger than the back, so the sides taper.
  2. Tape the box together. Join the panels with tape on the outside, leaving the front open.
  3. Line the inside. Glue foil, mylar or an emergency blanket inside the box with spray adhesive. Work in a ventilated area.
  4. Add the front diffuser. Tape the diffusion across the open front, pulled taut so it does not sag.
  5. Add an inner baffle (optional). A second diffusion layer halfway into the box evens out hotspots.
  6. Mount the light. Cut a hole in the back for an LED bulb socket, or mount a speedlight through the back. Add a bracket for a light stand or umbrella mount.

Light source: LED or speedlight

  • LED bulb. Choose a bulb with CRI 90 or higher and a color temperature of about 5000 to 5600K. Leave vent holes near the socket, because even LEDs build heat in an enclosed box.
  • Speedlight. Zoom the head wide, around 24 mm, or aim it into the back wall of the box so the light bounces around inside and fills the front evenly. A narrow zoom gives a bright center spot.

Grids and inner baffles

A cardboard egg-crate grid on the front narrows the spill, so more of the light falls on the subject. An inner baffle, as described above, spreads light more evenly inside the box. Use one or both if you see hotspots or unwanted spill.

Placement

  • Place the softbox at about 45 degrees to one side of the subject, slightly above eye level.
  • Keep it about one diagonal width away, as a starting point.
  • Put a reflector on the opposite side to lift the shadows. See how to make a DIY reflector.

Cheap alternatives

  • A window. Tape diffusion over a window for a large, free softbox.
  • A shoot-through umbrella. A white shoot-through umbrella is a common purchased alternative. Prices vary, but they are often around $15 to $25.
  • A continuous light. If you want a steady light you can see before you shoot, a DIY LED panel gives continuous output.

Stability

Put a sandbag on the stand. Foam board and cardboard boxes are top-heavy, and a light stand can tip over.

Common mistakes

  • Assuming a softbox is soft by default. Move it far from the subject and it becomes a small, hard source.
  • Worrying too much about the foil. Which side of the foil faces out makes only a small difference.
  • Blaming the foil for hotspots. Hotspots usually come from the bulb you can see directly through the diffusion.
  • Using a narrow speedlight zoom. It gives a bright center spot. Zoom wider or bounce the light.

Safety

  • Never put incandescent or halogen bulbs in a cardboard or paper softbox.
  • Even LEDs build heat in an enclosed box. Leave vent holes near the socket.
  • Secure the stand with a sandbag, because DIY boxes are top-heavy.

The complete guide to diy lighting

DIY Photography Lighting: Homemade Ideas That Work
Read the guide

Keep exploring

Guides from other topics

All topics →