Creative Lighting

How to use a fog smoke machine?

How to use a fog smoke machine: choose the right fluid, warm up, fire short bursts, let the fog spread, and light it from the side or behind.

On this page
  1. Types of fog and haze machines
  2. Fluid: use only the recommended type
  3. Warm-up and bursts
  4. Let the fog spread
  5. Outdoors and wind
  6. Power and size
  7. Maintenance and storage
  8. Lighting the fog
  9. Common mistakes
  10. Safety

Fill the tank with the fluid the maker recommends, wait for the ready light, fire short bursts, and give the fog 30–60 seconds to spread before you shoot. Light it from behind or from the side, because front light hides it. For the lighting side, see how to make fog visible on camera.

Types of fog and haze machines

  • Fogger: dense fog that clears quickly.
  • Hazer: fine particles that hang for longer and spread evenly. Good for visible beams.
  • Low-lying fog: dry ice in warm water, or a chilled unit, that stays near the floor, around knee height.
  • Ultrasonic: a water mist.
  • Handheld battery units and canned aerosol haze: for small or one-off shots.

Fog and haze machines are not the same. Haze is finer and lasts longer.

Use the water-based glycol or glycerin fluid that the manufacturer recommends. Do not use homemade mixes or other fluids. Wrong fluids can clog the heater, and some can be toxic. Unplug the machine before you refill it. Run cleaning fluid through it periodically, as the manual directs, to prevent clogs. Never run the pump dry, because it can burn out.

Warm-up and bursts

  • Heat-based units usually take about 3–10 minutes to warm up. Wait for the ready light. Warm-up time varies by model.
  • Fire short bursts, about 2–5 seconds each, with the remote. Don’t hold the button down.
  • Many budget units must reheat between bursts, often for 30–60 seconds. This varies.
  • Holding the button for more fog overwhelms the scene and can overload the heater.

Let the fog spread

Give the fog 30–60 seconds to spread before you shoot. A low fan can help it spread evenly. Indoors, close the doors and turn off the HVAC so the fog lingers.

Outdoors and wind

Wind clears fog quickly. Place the machine upwind of the scene so the fog drifts across it, and shoot right away.

Power and size

Consumer fog machines are often rated at 400–1,500 W. Higher wattage gives more output and faster reheating. Fluid use varies widely. Small units can use roughly a liter an hour of continuous running, so check the manual before a long shoot.

Maintenance and storage

  • Clean the machine periodically, as the manual directs.
  • Empty the tank before transport or long storage.

Lighting the fog

Backlight or side-light the fog, because front light hides it. For the full approach, see how to make fog visible on camera.

Common mistakes

  • Using any fluid, or a homemade mix. Wrong fluids clog heaters and can be toxic.
  • Holding the button down for more fog. It overwhelms the scene.
  • Treating fog and haze as the same. Haze is finer and lasts longer.
  • Assuming fog won’t set off alarms. Photoelectric smoke detectors often trigger.
  • Thinking dry ice is just cold fog fluid. Dry ice is frozen CO2 and has its own hazards.

Safety

  • The nozzle and the output are hot. Keep the machine at least 1 m (3 ft) from people and objects.
  • Ventilate between takes. Fog can irritate asthma and sensitive airways.
  • Fog residue makes floors slippery. Mop up after the shoot.
  • Dry ice needs gloves and good ventilation. Never seal it in a container.
  • Tell venue staff before you start. Some venues need the alarms isolated.

The complete guide to creative lighting

Smoke and Fog Photography Lighting
Read the guide

Keep exploring

Guides from other topics

All topics →