Short answer
Start with one key light, about 40 to 45 degrees to the side of your subject and slightly above eye level, with a softbox or umbrella on it. Add fill by placing a reflector on the opposite side, or by using a second light set about one to two stops lower. Set your camera to manual with a starting point such as ISO 100, then adjust flash power and aperture from a test shot.
Start with one light
You don’t need three lights to start. One light plus a reflector is a complete beginner setup. Learn how one light shapes the face before you add more.
Key light position
The key light is the main light. Place it about 45 degrees to the side of the subject and about 30 to 45 degrees above eye level. This puts the shadow gently under the cheekbone and jaw.
Lights placed straight in front of the subject, at camera height, give flat and unflattering results. Moving the light to the side adds depth and contrast.
Fill: reflector or second light
Fill softens the shadows on the side away from the key. You can use:
- A reflector on the opposite side. It bounces light from the key back into the shadows and adds no new light.
- A second light set about one stop lower than the key. One stop between key and fill is roughly a 2:1 ratio. Two stops is roughly 4:1. The way ratios are counted varies, so treat these as rough guides.
Camera settings for a first session
Set the camera to manual with these starting points:
- ISO 100 for clean image quality.
- Shutter speed at or below the flash sync speed. Many cameras sync around 1/125 to 1/200 s, but check your camera’s manual.
- Aperture around f/5.6 to f/8 for a balance of depth and light.
- White balance set to the flash or daylight preset, around 5500K, or a custom value.
Turn off room lights where you can. Mixed color temperatures from ceiling lights and flash cause color casts that are hard to fix in editing.
Flash power, aperture and shutter speed
With flash, shutter speed controls the ambient light, and aperture together with flash power and distance controls the flash exposure. In practice:
- Use the shutter speed to set how much room light shows up in the frame.
- Use the aperture and flash power together to set the exposure on your subject.
- Move the light closer or farther to change its strength. Inverse square law applies: doubling the distance cuts the light to a quarter, which is about two stops less.
Raising the shutter speed above the sync speed won’t darken the flash exposure, and on many cameras it causes a black band across the frame.
Check the exposure with a test shot
Take a test shot, then check the histogram or the highlight warnings on the back of the camera. A handheld light meter gives exact readings if you have one. Adjust flash power or distance until the face is exposed well, and then take another test.
Use modeling lamps or continuous light to preview shadow placement before you fire the flash, if your light has them.
Background and subject distance
Keep the subject about 1 to 2 m (3 to 6 ft) from the background. A subject too close to the background casts shadows on it.
To darken the background, move the subject farther from it. To brighten the background, light it separately.
Optional third light
A hair or rim light placed behind the subject, opposite the key, separates the subject from the background. Add it once the key and fill are working well, and you have a classic three-point lighting setup.
Common mistakes
- Using too much flash power. More power isn’t better. Overexposure and too few low-power settings are common beginner problems.
- Relying on continuous light for exposure. Continuous lights are easier to preview but much weaker than flash.
- Ignoring white balance. Set it to match the light you’re using.
- Skipping sandbags. Lightweight stands tip easily, especially with softboxes.
Safety
- Sandbag stands, especially with softboxes.
- Tape down cables so no one trips on them.
- Halogen modeling lamps get very hot. Keep them away from fabric.
Once your setup works, compare modifier shapes in octabox vs rectangular softbox. For umbrella placement, see how to use a white umbrella in photography. For a reflector as fill, see how to use a silver light reflector. If you’re still deciding what to buy, the best studio lighting kits guide covers the options.